A single-component fast-drying alkyd primer enamel with a non-volatile content contains anti-corrosion additions that increase protective properties of the formed coating.
It is designed for painting metal, concrete with a long-term operation of up to 7 years. It has increased adhesion to metal, concrete and wood surfaces, so it does not require preliminary priming of the work surface.
It can be applied by air or air-free methods of dispersing, as well as with a roller or brush. Due to the low toxicity of contained solvents, the primer enamel is easy to apply. It can be used as primer or an independent coating
Color of the primer enamel is according to the RAL scale.
Name of indicator and unit of measurement
Physical form of the coating
Self surface without any impurities, bits and pin holes
Non-volatile matter content, %, not less
Conditional viscosity by viscometer VZ-246 with nozzle diameter 4 mm at temperature (200 С) , s
from 60 up to 120
Density at temperature (20±0,5) °С, g/cm3
From 1,2 up to 1,4
Milling degree, µm, not more
Adhesion, points, not more
Flexural resistance, mm, not more
Impact strength, cm, not less
Recommended coating thickness, µm
from 80 up to 120
Drying time of a layer 60 microns up to degree 3 at a temperature 25 ºС, minutes, not more
Time of full cure of the coating at Т= 20°С, days, not more
Coverage rate, g/m2., not more
Hardness by the pendulum device TML type (pendulum А), conventional units, not less
Resistance to the exposure to sea water, hrs (20°C, ) not less
Resistance to the exposure to water, hrs (20°C, ) not less
Resistance to the exposure to industrial oil, hrs(20 °C, ) not less
Requirements to the base
The metal surface should be dry, free of rust, debris, dust, oils, fats and other contaminants that may act as separators. If necessary, handle the base with a sand- and bead-blasting method to degree Sa 2-2,5 (ISO 8501-1:2007). After cleaning, the surface should be removed from dust and degreased.
Cement-containing and stone surfaces should be clean, dry (humidity is not more than 5%), without traces of bleed water, dirt, oil, as well as withstand design loads (compression capacity is not less than 200 kp/cm2), contain no fragile and stuck-on particles. If necessary, handle the base with a sand- and bead-blasting method, milling or polishing. After processing, the surface should be removed from dust and saturated with the DEFENS materials.
Previously painted surfaces suitable for repainting. Remove impurities (e.g., grease and salts). Surfaces must be dry and clean. Old surfaces with a painting that has exceeded the maximum application time of the next coat should be ground to roughness. Damaged surface areas should be handled in accordance with accepted procedures on how to prepare the base and maintenance operations. Place and time of prefinishing of the surface for applying the paint should be chosen so that the neat surface remains dry and clean until the next stage of painting the product.
Before applying, the primer enamel should be thoroughly mixed for at least 5 minutes until an even consistency is obtained. Apply it on the prepared base by air or air-free methods of dispersing, as well as with a roller or brush. To obtain the material of necessary application viscosity, it is possible to add a mixed solvent. The surface to be painted should be dry and have a temperature of a 3 °С above the dew point. Recommended number of layers is 1-2. Perform the work in accordance with the ISO 12944-7:2017 standard
Package and storing
The paint is stored in a tightly closed packaging at a temperature from -20 up to +30°С, away from moisture and direct sunlight, heat sources. Warranted storage life is 12 months from the date of production without violation of storage conditions. Slight delamination is allowed during the long-term storage, but it does not affect the quality of the material.
Work tools and facilities are washed with solvent or xylele immediately after their usage.
This product is intended only for professional use in industrial facilities in accordance with recommendations given here, as well as safety directions provided to customers along with paint containers. All work, including the application and usage of the product, must comply with Health, Safety and Environmental requirements, all regional standards and instructions.
When painting use personal protective equipment, avoid of getting in eyes, respiratory tracts and on skin. Keep away from open flame.