One-component paint is intended for drawing horizontal marking of the carriageway of highways, pedestrian crossings, parking lots, production and storage premises and other asphalt and cement and concrete surfaces.
One-component paint is intended for drawing horizontal marking of the carriageway of highways, pedestrian crossings, parking lots, production and storage premises and other asphalt and cement and concrete surfaces. Provides resistance to abrasion, water, saline solutions, cold and ultraviolet. Drying time to degree 3 at (20 ± 2) ° C is not more than 20 minutes.
Kraska Defens RO AD submityaet is pyhmentov suspensions and napolnyteley soluble in akrylovoy smolы funktsyonalnыmy with additives and rastvorytelem. Adding glass beads in a ratio of 20-30% by weight forms a reflective coating
Purpose and scope
Paint is used for horizontal marking of carriageways, pedestrian crossings, parking lots, production and storage facilities and other asphalt and cement concrete surfaces.
1 Enamel coating color
white or yellow.
2 The appearance of the coating
matt, homogeneous surface
3 Conditional viscosity at (20 ± 2) ºС, according to the VZ-246 viscometer with a nozzle diameter of 6 mm, s, not more than
4 Mass fraction of non-volatile substances,%, not less
5 Degree of milling, microns, not more than
6 Drying time to degree 3 at (20 ± 2) ° C and relative humidity (65 ± 5)%, min, not more than
7 Bending film elasticity, mm, max
8 Film adhesion, points, max
9 Stability of coating to static action of water at (20 ± 2) ° С, h, not less
10 Stability of coating to static action of 3% sodium chloride solution at (20 ± 2) ° C, h, not less
11 Coordination of the x and y coordinates of the area of the angular points of the color areas of the road marking
resistant to water and salt solutions;
resistance to cold and ultraviolet;
Method of application
Surface preparation. The paint is applied on a dry surface, cleaned of dust, sand, oils and other contaminants. The humidity of the concrete base should be no more than 18%, asphalt - no more than 10%. The pavement should be free of pits and deformations and, if necessary, washed and dried.
In the case of marking a new asphalt concrete coating, the paint is applied at least 5 days after its laying.
The surface temperature should be at least 3 ° C above the dew point.
Before application the paint is thoroughly mixed, if necessary, diluted to working viscosity with solvent or xylene in an amount of not more than 5%. The introduction of a significant amount of solvent may result in a film that is too thin and, consequently, reduce the service life of the coating.
Working conditions. The paint is applied at a steady air temperature from +5 to + 30 ° C and relative humidity - no more than 80%.
The temperature of the base on which the paint is applied should be in the range from +5 to + 45 ° C.
To make arrangement of technical means of the organization of traffic according to the approved schemes of fencing of places of production of work, VSN37-84 and GOST 23457-86
It is not allowed to carry out work with significant humidity of the air or the base - with precipitation, during the fall of fog or dew.
- with the help of special marking machines,
- by the method of pneumatic spraying,
- brush or roller.
Rashod « Defens RoAD »: 600- 700 g / m² with a wet layer thickness of 400-600 microns.
Consumption of glass beads ( fr 100-600 microns) -300-350 g / m²
The paint is stored in a tightly closed container, protecting from moisture and direct sunlight, away from heat sources, at a temperature of -30 to + 30 ° C. The warranty period of storage is 6 months from the date of manufacture. A slight bundle is allowed for long-term storage.
Cleaning the tool
Work tools and equipment are washed with solvent or xylene immediately after use
When carrying out painting work, use individual means of protection, avoid contact with eyes, respiratory system and skin. Keep away from fire.